該頁無縮略圖
Continuous Fiberglass Strip Reinforced PE Composite Pipe for Water Supply
Excellent Structure, Assured Quality
Manufacturedwithhigh-qualityPErawmaterialsand high-strengthmaterialsthroughthree-layercompositetechnology, itfeatureshighstrength,goodtoughness,lightweight, corrosionresistance,andlongservicelife.
Newonlinemoldhot-melt cavitymoldingsealingtechnol ogy，withhigherefficiencyand betterquality.
Thereinforcementlayeris pre-impregnatedfiberglass strip,whichisthermallyfused andbondedwiththe innerand outerlayers.Itsintegrated
Theinnerandouterlayersare madeofspecialPEmaterials forpipes,withsmoothsurfac es,corrosionresistance,and longservicelife.
Product Introduction
The continuous fiberglass strip reinforced PE composite pipe is a new type of structural wall pipe composed of three layers: polyethylene-based resinas the innerand outer layers,and fiberglass composite strip pre-impregnated with polyethylene resinas the reinforcing layer through continuousspiral windingand fusion.
Compared with PE solid-wall pipes,it significantly improves pressure resistance and expands application fields.Italso enhances temperature resistance,impermeability,chemical corrosion resistance,andscratch resistance.
Product Specifications
Continuous Fiberglass Strip Reinforced PE Composite Pipe for Water Supply
| Nominal Outside Diameter(mm) | NominalPressure (MPa) | Delivery Method |
| 50 | 3.5 | CoiledDelivery (Straightpipesavailable upon request) |
| 63 | 3.5 | |
| 75 | 3.5 | |
| 90 | 3.5 | |
| 110 | 1.6、2.5、3.5 | Straight Pipe Delivery |
| 160 | 1.6、2.5、3.5 | |
| 200 | 1.6、2.0、2.5 | |
| 250 | 1.0、1.6、2.0、2.5 | |
| 315 | 1.0、1.6、2.0、2.5 | |
| 400 | 1.0、1.6、2.0、2.5 | |
| 500 | 1.0、1.6、2.0、2.5 | |
| 630 | 0.8、1.0、1.6、2.0 |
Material Requirements
●Performance Requirements for PolyethyleneMaterials
1) Polyethylene resin of PE1o0 grade orabove must be used.
2) Clean virginmaterialsmust be used entirely for pipe manufacturing,and recycledmaterialsorreclaimed materials ofany formand fromanysourceareprohibited.
●Performance Requirements for Polyethylene Fiberglass Strip The fiberglass filaments shal meet the requirements of GB/T18369. The polyethylene fiberglass strip shall meet the requirements in the following table.
| Item | Indicators | TestMethod |
| Appearance | Itssurfaceshallbesmoothand flat, withoutdelamination,exposed or detached fiberglass,andwithoutobvious defectssuchasscratches,holes, wrinkles,bubbles,depressions,tc. | Visual Inspection |
| WidthDeviation/mm | It shall not exceed±5% ofthenominalvalue | GB/T6673 |
| Thickness Deviation/mm | Itshall notexceed±10%of thenominalvalue | GB/T6672 |
| TensileStrength/MPa | ≥700 | GB/T1040.5 |
Applications
●Municipal Engineering: Water supply for urban buildings,drinking water transportation;
* Chemical Industry: Process pipes and discharge pipes for transporting corrosive liquids in industries such as acid,alkali,and salt production,textiles,printing and dyeing;
* Metallurgical Mines:Fiber-reinforced polyethylene liquid pipes for mining and coal mines;
* Fire Water:Transportation of urban fire water;
* Pipes foragricultural irrigation;
Performance Indicators
The performance indicators of the pipes meet the requirements of GB/T 43o05-2023 Composite Pipes of Polyethylene Reinforced with Continuous Wound Glass-Fiber-Tape for Water Supply.
1.Requirements for Hydrostatic Strength and Burst Pressure Tests
| Test Type | Tempeature | Test Pressure | Test Time | Requirements |
| Hydrngtic | 20 | Nominal pressure | 1 | No ruature |
| 60 | Nominal.presue | 165 | No rupture, | |
| 60 | Nominal pressure ×1.25 | 1000 | No rupture, noleakage | |
| BurstPressure | 20 | ≥4 times the nominal pressure | Burst |
| Item | Requirements |
| MeltMassFlowRate (190°℃，5kg)/(g/10min) | Thechange in polyethylene MFRbeforeand afterprocessing shall not exceed±20% |
| Oxidation Induction Time (210℃)/min | ≥20 |
| Longitudinal Reversion (e≤16mm)1% | ≤1.5 |
| Compressioncrackingstability | Nocracks,delamination,orcracking |
| Long-termLifeVerification | 20 yearsabove ground,50 yearsunderground |
3.Hygienic Performance The hygienic performance of pipes used to transport drinking watershall complywith the requirements of GB/T 17219.
Pipe Connection
The continuous fiberglass strip reinforced PE composite pipes can adopt different connection methods in different applications.The specific connection methods areas follows: ① Electrofusion connection ② Metal crimping connection
LESSO
Product Advantage Analysis
Compared with steel wire mesh pipes of the same specification and pressure rating,the weight of continuous fiberglass strip reinforced PE composite pipes is reduced by approximately 1 5 \small { ~ } 3 0 % Compared with PE solid-wall pipes,theweight is reduced byabout 3 0 % ~ 4 0 % .Compared with steel skeleton PEcomposite pipes,theweight is reducedby over 3 5 % .The higher the pressureand diameter,the more significant the weight advantage.
Continuous fiberglass strip reinforced PE composite pipes of the same specification can achieve higher pressure ratings,up to 3.5Mpa currently.
| Category | PE Solid- Wall Pipe | Steel WireMesh PE Composite Pipe | SteelSkeleton PE Composite Pipe | Continouns ficer PEs Composite Pipe |
| Pipe Cost | High | Relatively High | High | Low |
| PipeWeight | Heavy | Heavy | Heavy | Light |
| Production Speed | Fast | Slow | Slow | Fast (SameasPEPipes) |
| Design Pressure (Mpa) | 1.0、1.6 | 1.0、1.6 | 1.0-2.5 | 1.0、1.6、2.0、2.5、3.5 |
| Applicable Temperature | 40°℃ | 40℃ | 40°℃ | 40℃ |
Product Features
The inner layer,fiberglass reinforced layer, andouterlayerareallformedbyPEmatrix resin intoauniform integrated structure,with hot-melt bonding between layers.
No sealing rings are used; Integrated simple process,high efficiency, Electrofusion hot-melt noexposed fiberglass layers, connection and bonding and good sealing quality. metal crimping structure Convenient New connection extrusion
Light weight, coiled sealing
deliveryavailable, technology
convenient for Outstanding
loading,unloading,
and transportation. performanceof continuous 1 Light fiberglass strip weight reinforced PE Corrosion/ composite pipe wear resistance Strong bearing capacity Smooth High strength and inner Smooth inner wall, no strongcompressive wall scaling,lowwater flow capacity. friction resistance, higl water transmission efficiency,and reduced
Innerand outer layers use special PE materials for pipes, withexcellent corrosion resistance, wear resistance,and long service life.
energy consumption.
LESSO GROUP
Hotline: +86 4009212800 (Ext. 1701) E-mail:oversea@lesso.com Website:www.lesso.com
\*Thiscatalog has beenpreparedasasupport guide. Undernocircumstanceshall LESSO assumeany liabilityorresponsibilitywiththe informationinthiscatalog. EveryefforthasbeenmadebyLESsOtoprovideaccurateanduptodateinformation.
All Rights Reserved 2025.10
